Home - Waterfall Grid T-Grid Console Builders Recent Builds Buildslaves Changesources - JSON API - About

Console View

Legend:   Passed Failed Warnings Failed Again Running Exception Offline No data

eb087ae4f46a...
Rui Salvaterra
ath79: move the squashfs feature to the parent target
All subtargets define it. Move it to the parent target and remove
it from all subtargets.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
e065c9184cd1...
Daniel Golle
uqmi: update to git HEAD
65796a6 nas: add --get-plmn
0a19b5b uqmi: add timeout parameter

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
dd4e6a70f2f4...
Rui Salvaterra
hostapd: enable the epoll-based event loop
Hostapd supports epoll() since 2014. Let's enable it for better performance.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
ce293cd3ac3a...
Filip Moc
uqmi: set device-operating-mode to online
This is required for LTE module MR400 (in TL-MR6400 v4).
Otherwise LTE module won't register to GSM network.

Signed-off-by: Filip Moc <lede@moc6.cz>
cdff729b2759...
Pawel Dembicki
layerscape: enable spi-uart in LS1012A-FRDM
This patch add missing support of SC16IS740 serial controller, installed
on LS1012A-FRDM board.

It was required to change RCW bits, because SPI was disabled by default.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
cba79b1de2d2...
Yanase Yuki
ath79: move device specific nodes to DTS files for Devolo 1xxx
qca9558_devolo_dvl1xxx.dtsi contains device specific nodes which
are inherited for some DTS files and overwritten for others.

This is considered confusing, so move the relevant nodes/properties
to the devices and only keep the shared stuff in the DTSI.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[clarify commit title/message, move &gmac_config in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
c0af4a0ca259...
Vladimir Vid
mvebu: add initial support for Globalscale ESPRESSObin-Ultra
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.

- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot

** Installation **

Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/

Connect to the device UART via microUSB port on the back side and power on the device.

Power on the device and hit any key to stop the autoboot.

Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device

Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive

Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb

Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r

Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.

Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync

Reboot the device.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
bc64b9c32e00...
Tomasz Maciej Nowak
treewide: update email address of Tomasz Maciej Nowak
Replace my o2.pl email address.

I'm still available at the old address.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
b4b829fe6490...
Martin Schiller
uqmi: set plmn only if necessary
Setting the plmn to '0' (auto) will implicitly lead to a (delayed)
network re-registration, which could further lead to some timing
related issues in the qmi proto handler.

On the other hand, if you switch back from manual plmn selection
to auto mode you have to set it to '0', because this setting is
permanently "saved" in the wwan module.

Conclusion:
If plmn is configured, check if it's already set euqally in the module.
If so, do nothing. Otherwise set it.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
b19a684f4619...
Paulo Machado
imagebuilder: fix main entry makefile
Remove a syntax error from ImageBuider Makefile

Acked-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Paulo Machado <pffmachado@yahoo.com>
b11ad4876440...
Sander Vanheule
ath79: support for TP-Link EAP245 v1
TP-Link EAP245 v1 is an AC1750 (802.11ac Wave-1) ceiling mount access point.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9880): a/n/ac, 3x3
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE

Flashing instructions:
* Upgrade the device to firmware v1.4.0 if necessary
* Exploit the user management page in the web interface to start telnetd
  by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
  (e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
  patch listed below. The patch is required to prevent `uclited -u` in
  the last step from crashing.
* Copy the patched uclited programme back to the device at /tmp/uclited
  (via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.

    --- xxd uclited
    +++ xxd uclited-patched
    @@ -53796,7 +53796,7 @@
    000d2240: 8c44 0000 0320 f809 0000 0000 8fbc 0010  .D... ..........
    000d2250: 8fa6 0a4c 02c0 2821 8f82 87b8 0000 0000  ...L..(!........
    -000d2260: 8c44 0000 0c13 45e0 27a7 0018 8fbc 0010  .D....E.'.......
    +000d2260: 8c44 0000 2402 0000 0000 0000 8fbc 0010  .D..$...........
    000d2270: 1040 001d 0000 1821 8f99 8374 3c04 0058  .@.....!...t<..X
    000d2280: 3c05 0056 2484 a898 24a5 9a30 0320 f809  <..V$...$..0. ..

Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
      Do NOT bridge R230.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

Tested on the EAP245 v1 running the latest firmware (v1.4.0). The binary
patch might not apply to uclited from other firmware versions.

EAP245 v1 device support was originally developed and maintained by
Julien Dusser out-of-tree. This patch and "ath79: prepare for 1-port
TP-Link EAP2x5 devices" are based on that work.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
b0ecae504b58...
Sander Vanheule
ath79: support for TP-Link EAP225 v3
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access
point. Serial port access for debricking requires fine soldering.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 3x3
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE

Flashing instructions:
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R225 (TXD) and R237 (RXD).
      Do NOT bridge R230.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM boot log:

    Using interface ath0 with hwaddr b0:...:3e and ssid "..."
    Using interface ath10 with hwaddr b0:...:3f and ssid "..."

Tested by forum user blinkstar88

Signed-off-by: Sander Vanheule <sander@svanheule.net>
aab36200e7eb...
Matthew Gyurgyik
imagebuilder: fix partition signature
When building images with the imagebuilder, the partition signature
never changes. The signature is generated by hashing SOURCE_DATE_EPOCH
and LINUX_VERMAGIC which are undefined. Prepopulate these variables, as
done by the SDK.

Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
a1158b3170b9...
Pawel Dembicki
kernel: iio: add fxas21002c driver support
This patch adds kernel modules for Freescale FXAS21002C 3-axis gyro driver.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
9ebbb5511392...
Filip Moc
uqmi: add support for IPv4 autoconf from QMI
There already was an option for autoconfiguring IPv4 from QMI but this
was removed by commit 3b9b963e6e08 ("uqmi: always use DHCP for IPv4").

DHCP does not work on MR400 LTE module (in TL-MR6400 v4) so let's readd
support for IPv4 autoconf from QMI but this time allow to configure this
for IPv4 and IPv6 independently and keep DHCP default on IPv4.

Signed-off-by: Filip Moc <lede@moc6.cz>
991e6f8cccbf...
John Audia
linux-firmware: update to 20201118
git log --pretty=oneline --abbrev-commit 20201022..20201118
2ea8667 (tag: 20201118) rtlwifi: v88.2 firmware files for RTL8192CU
e850cf3 Merge https://github.com/rjliao-qca/qca-btfw into main
65370db rtw88: RTL8822C: Update firmware to v9.9.4
e371b7c Revert "rtw88: RTL8822C: Update firmware to v9.9.4"
51d2c81 vpdma: Move firmware to ti directory
d7a24c9 Merge branch 'master' of https://github.com/shahasit/video-linux-firmware into main
9ee1543 Merge branch 'master' of https://github.com/shahasit/bt-linux-firmware into main
3bcc4c1 amdgpu: update picasso VCN firmware
b6b4542 amdgpu: update raven2 VCN firmware
79aa335 amdgpu: update raven VCN firmware
c93834e rtw88: RTL8822C: Update firmware to v9.9.4
3ef6c93 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099A_281A
b503c96 Merge branch 'ath10k-20201023' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware into main
463fdea QCA: Update Bluetooth firmware for QCA6390
8a46c32 qcom : updated venus firmware files for v5.4
d7793e5 QCA : Fixed BT SSR due to command timeout / IO fatal error
d842d8c ath11k: QCA6390 hw2.0: add to WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
8fb1a6e ath11k: QCA6390 hw2.0: add board-2.bin
34cb5fc ath11k: IPQ8074 hw2.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
c0a8efd ath11k: IPQ8074 hw2.0: add board-2.bin
ac7f5e9 ath11k: IPQ6018 hw1.0: add to WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
2594e51 ath11k: IPQ6018 hw1.0: add board-2.bin
d8f10d4 ath10k: QCA6174 hw3.0: add firmware-sdio-6.bin version WLAN.RMH.4.4.1-00077
6652297 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00131
36059aa ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00131
1e5629d ath10k: QCA6174 hw3.0: update board-2.bin
e315d1a ath10k: QCA6174 hw3.0: update firmware-6.bin to WLAN.RM.4.4.1-00157-QCARMSWPZ-1

Signed-off-by: John Audia <graysky@archlinux.us>
97ac290090a5...
Daniel Golle
uhttpd: update to git HEAD
f53a639 ubus: fix uhttpd crash

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
910056626775...
John Audia
kernel: bump 5.4 to 5.4.79
Manually rebased patches:
  ath79/patches-5.4/910-unaligned_access_hacks.patch
  bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch
  bcm27xx/patches-5.4/950-0414-SQUASH-Fix-spi-driver-compiler-warnings.patch
  ipq806x/patches-5.4/093-4-v5.8-ipq806x-PCI-qcom-Use-bulk-clk-api-and-assert-on-error.patch

Removed since could be reverse-applied by quilt and found to be included upstream:
  ipq806x/patches-5.4/096-PCI-qcom-Make-sure-PCIe-is-reset-before-init-for-rev.patch

All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[refresh altered targets after rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
8dd2a1715b0a...
Sander Vanheule
ath79: ensure QCA956x gmac0 mux selects sgmii
Some bootloaders do not set up gmac0 properly, leaving it disconnected
from the sgmii interface. If the user specificies phy-mode sgmii, then
use the gmac-config/device node to ensure the mux is configured
correctly.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
89854d383492...
Álvaro Fernández Rojas
ath10k-ct: update to latest version
1d28d17 ath10k-ct: Fix RSSI reporting for wave-1 firmware.
0c2949e ath10k-ct: fwcfg allows configuring dma-burst setting.
13319ff ath10k-ct: stable patches, debugfs crashdump, 5.8 driver

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
87627b2d760c...
Julien Dusser
ath79: add QCA956x SERDES init workaround
This commit add a workaround for non working SGMII link observed on some
QCA956x SoCs. The workaround originates part from the U-Boot source code
from QCA, part from the implementation from TP-Link found in the GPL
tarball for the EAP245v1.

Extends commit 0d416a8d3b990e3b78628f0e7546527709c877f7 for QCA956x.
Note that reset is the same on QCA955x and QCA956x, same register offset
and values.

Auto calibration is done on u-boot, but always fall back to default value
0x7. Add a DTS entry serdes-cal in case a device require another value.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
[Sander Vanheule:
    Minor code style fixes,
    Remove hunk adding qca956x-serdes-fixup to a missing DTS,
    Remove variable err that was only assigned,
    Rename function to sgmii_serdes_init,
    Lower priority of serdes call message to pr_debug]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
8262c99fc366...
Daniel Golle
procd: update to git HEAD
04a2edd uxc: make force-delete kill container process
be6da62 seccomp: silence 'unknown syscall' warnings
b22e625 jail: cgroup hack: rewrite cgroup -> cgroup2
df7fa7b uxc: fix incomplete commit

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
8231994d3f02...
Sven Eckelmann
ipq40xx: DTS style updates for OpenMesh devices
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.

* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
7c114f33dd8c...
Paul Spooren
opkg: purge package from cache on hash mismatch
61b3c62 opkg_verify_integrity: better logging and error conditions
f73d42f download: purge cached packages that have incorrect checksum
1c1480e download: factor out the logic for building cache filenames
293b1ce libopkg: factor out checksum and size verification
a786e25 download: remove compatibility with old cache naming scheme

Signed-off-by: Paul Spooren <mail@aparcar.org>
7a875d155ed9...
Sander Vanheule
ath79: prepare for 1-port TP-Link EAP2x5 devices
TP-Link has developed a number of access points based on the AP152
reference board. In the EAP-series of 802.11ac access points, this
includes the following devices with one ethernet port:
* EAP225 v1/v2
* EAP225 v3
* EAP225-Outdoor v1
* EAP245 v1

Since the only differences between these devices are the ath10k wireless
radios and LEDs, a common base is provided for the overlapping support
requirements.

Hardware commonalities:
* SoC: QCA9563-AL3A MIPS 74kc v5.0 @ 775MHz, AHB @ 258MHz
* RAM: 128MiB DDR2 @ 650MHz
* Flash: 16MiB SPI NOR
* Wi-Fi 2.4GHz: provided by SoC
* Wi-Fi 5Ghz: ath10k chip on PCIe
* Ethernet: AR8033-AL1A, one 1GbE port (802.3at PoE)

Signed-off-by: Sander Vanheule <sander@svanheule.net>
6e9b707ee2bd...
Daniel Golle
Revert "refpolicy: add variant that builds modular policy"
This reverts commit 9eb9943f82e0b2d5e32ffe1c63f5a82caca5094d.
Building the 'modular' variant requires 'semodule_package' from
'selinux-python' to be installed on the buildhost.
Apart from that, this change also broke the monolithic refpolicy
'targeted' build.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6e1a4496f58c...
René van Dorst
ramips: phy: at803x: Select SFP interface mode that both sides supports.
Currently sfp_select_interface() return the fastest interface that
the sfp modules supports even if the phy don't support that mode.

For example an GPON module that support both 2500basex and 1000basex.
Currently sfp_select_interface() picks 2500basex instead of 1000basex.

So limit the interfaces which both sides supports before calling
sfp_select_interface() or return an error if we don't have match.

Reviewed-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Braihan Cantera <bcanterac@gmail.com> [MikroTik RB760iGS + Nokia G-010S-A 3FE46541AA SFP]
Tested-by: John Thomson <git@johnthomson.fastmail.com.au> [Mikrotik rb760igs + SFP SM/LC, SFP base1000T, SFP+ passive DAC]
Signed-off-by: René van Dorst <opensource@vdorst.com>
65f8d7360c04...
Pawel Dembicki
layerscape: make initramfs kernel fit packed
This will make developing process easier, because dtb will be included
into image.
Not need to enable initramfs image by default.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
651f0c09999f...
Leon M. George
hostapd: fix patch offset
Fixes the offset of the patch added in 93bbd998aa696a
  ("hostapd: enter DFS state if no available channel is found").

Signed-off-by: Leon M. George <leon@georgemail.eu>
5bb3cc749ee0...
Jan Pavlinec
tcpdump: patch CVE-2020-8037
This PR backports upstream fix for CVE-2020-8037.  This fix is only
relevant for tcpdump package, tcpdump-mini is not affeted by this issue.

Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
4f86edf477ed...
Sander Vanheule
ath79: support for TP-Link EAP225-Outdoor v1
TP-Link EAP225-Outdoor v1 is an AC1200 (802.11ac Wave-2) pole or wall
mount access point. Debricking requires access to the serial port, which
is non-trivial.

Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (AR8033): 1× 1GbE, PoE

Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface

Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
  * Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:

    ath0      Link encap:Ethernet  HWaddr D8:...:2E
    ath10    Link encap:Ethernet  HWaddr D8:...:2F
    br0      Link encap:Ethernet  HWaddr D8:...:2E
    eth0      Link encap:Ethernet  HWaddr D8:...:2E

Tested by forum user PolynomialDivision on firmware v1.7.0.
UART access tested by forum user arinc9.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
4dc27a026b7e...
Pawel Dembicki
layerscape: add i2c peripherials on LS1012A-RDB
LS1012A-RDB equipped in some i2c devices:
  - 3x GPIO Expander: PCAL9555A (NXP)
  - Gyro: FXAS21002 (NXP)
  - Accelerometer: FXOS8700 (NXP)
  - Current & Power Monitor: INA220 (TI)

This patch enables i2c peripherials installed on LS1012A-RDB.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
479981074539...
Felix Fietkau
netifd: update to the latest version
213748a9bcd9 system-linux: implement full device present state management for force-external devices
3abe1fc87151 system-linux: add retry for adding member devices to a bridge

Signed-off-by: Felix Fietkau <nbd@nbd.name>
39fa0c0959c7...
Hannu Nyman
tools/mpc: update to 1.2.1
Update mpc to 1.2.1

http://www.multiprecision.org/mpc/
  Bug fixes:
    Fix an incompatibility problem with GMP 6.0 and before.
    Fix an intermediate overflow in asin.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2eb0d711a455...
Daniel Golle
procd: update to git HEAD
d4d78db uxc: also delete procd runtime state on 'delete'
e935c0c jail: add 'debug' extern variable to preload_seccomp

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2b3a0cabea33...
Thomas Richard
uqmi: wait forever registration if timeout set to 0
Give possibility to wait forever the registration by setting timeout
option to 0.

No timeout can be useful if the interface starts whereas no network is
available, because at the end of timeout the interface will be stopped
and never restarted.

Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
223eec7e81f8...
Sven Eckelmann
kernel: mtd: parser: cmdline: Fix parsing of part-names with colons
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:

  root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait

The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:

  KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)

Such a partition list cannot be parsed and thus the device fails to boot.

Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.

Fixes: d6a9a92e3217 ("kernel: bump 5.4 to 5.4.69")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
1e69106e348e...
Filip Moc
generic: add DTR quirk patch for MR400 LTE
This is required for LTE module MR400 in TL-MR6400 v4.

Signed-off-by: Filip Moc <lede@moc6.cz>
0d65177658df...
Filip Moc
ramips: add support for TP-Link MR6400 v4
You can flash via tftp recovery:
- serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
- connect to any ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button

Flashing via OEM web interface does not work.

LTE module does not support DHCP so it must be configured via QMI.

Hardware Specification (v4.0 EU):
- SoC: MT7628NN
- Flash: Winbond W25Q64JVS (8MiB)
- RAM: ESMT M14D5121632A (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 1NIC (4x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 9V 0.85A

Signed-off-by: Filip Moc <lede@moc6.cz>
0c87304d2be2...
Paul Spooren
scripts: add size_compare.sh
As package size changes are a continuous topic on the mailing list this
scripts helps developers to compare their local package modifications
against latest upstream.

The script downloads the latest package indexes based on env variables
or the `.config` file. The script compares the actual installed size
(data.tar.gz) or the IPK package size.

An example output is found below:

```
user@dawn:~/src/openwrt/openwrt$ ./scripts/size_compare.sh
Compare packages of ath79/tiny/mips_24kc:
dropbear busybox iw ubus

Checking configuration difference
  % Total    % Received % Xferd  Average Speed  Time    Time    Time  Current
                                Dload  Upload  Total  Spent    Left  Speed
100  554  100  554    0    0    336      0  0:00:01  0:00:01 --:--:--  336

--- start config diff ---
--- /tmp/config.DDjwVh-LOCAL 2020-11-23 09:08:28.913203068 -1000
+++ /tmp/config.DDjwVh-UPSTREAM 2020-11-23 09:08:36.369240887 -1000
@@ -1,5 +1,9 @@
+CONFIG_ALL_KMODS=y
+CONFIG_ALL_NONSHARED=y
CONFIG_AUTOREBUILD=y
+CONFIG_AUTOREMOVE=y
--- 8< ---
CONFIG_BINARY_FOLDER=""
+CONFIG_BUILDBOT=y
+CONFIG_TARGET_ALL_PROFILES=y
CONFIG_TARGET_ROOTFS_DIR=""
CONFIG_USE_SSTRIP=y
CONFIG_USE_UCLIBCXX=y
--- end config diff ---

Checking installed size

Fetching latest package indexes...
  % Total    % Received % Xferd  Average Speed  Time    Time    Time  Current
                                Dload  Upload  Total  Spent    Left  Speed
100 80634  100 80634    0    0  33499      0  0:00:02  0:00:02 --:--:-- 33485
  % Total    % Received % Xferd  Average Speed  Time    Time    Time  Current
                                Dload  Upload  Total  Spent    Left  Speed
100 54082  100 54082    0    0  24252      0  0:00:02  0:00:02 --:--:-- 24252

Comparing package sizes...
Change Local Remote Package
+271 51386 51115 base-files
+123 705241 705118 bnx2-firmware
+86 17209 17123 fstools
+22 47989 47967 procd
+21 208311 208290 busybox
+19 67181 67162 netifd

```

I plan to integrate this script into the CI so we have a summary how
sizes change over different architectures.

Signed-off-by: Paul Spooren <mail@aparcar.org>